| By
Johan Leuridan and Alain Foncé
In
this manual we let you share the experience gained
during many years of practical situations when applying
the HSH range of products. All detailed information
can be found in the relevant Technical and Material
Safety Data sheets, an excerpt of the technical
information is written in the last chapter of this
booklet.
For
16 commonly used substrates we advise on how to
treat and apply the HSH primers, fillers and topcoats.
1.
Aluminium, not painted page 2
2.
Aluminium, painted page 3
3.
Decorative film page 4
4.
Decorative film, slightly damaged page 5
5.
Decorative film, heavily damaged page 6
6.
Honeycomb, new page 7
7.
Honeycomb, painted page 8
8.
Kydex panels page 9
9.
Laminate page page10
10.Leather,
artificial leather and p.u.foampage 11
11.MDFpage
12
12.Meal
trayspage 13
13.Melamine
and hardboardpage 14
14.Panellite
page15
15.Plastic,
not painted page16
16.Plastic,
painted page17
Excerpt
Technical Information page18
1
ALUMINIUM, NOT PAINTED
PRETREATMENT
Gently
scuff sand the surface with Scotch Brite red type
A very fine or sanding paper grade P320 or P240
Use INTERPLAN EED or Iso Propyl Alcohol with clean
cloths (wipe on, wipe off) to degrease the surface
APPLICATION
Apply
a thin coat of INTERPLAN 750M metal primer.
1) viscosity :30-40 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle 1.8 mm
Allow
to dry for a few minutes at 20°C = 68°F
Add
maximum 4 % by weight INTERPLAN Enhancer to INTERPLAN
1065B
for better cleanability and optimal smoke and stain
resistance
Spray
a coat of INTERPLAN 1065B 1) viscosity 40-45 sec
Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F,
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
2 ALUMINIUM, PAINTED
PRETREATMENT
Dry
sand with sanding paper grade P320 or P380
Clean
surface with a clean damp cloth or Iso Propyl Alcohol.
APPLICATION
If
the sanded paint is HSH PAINT apply INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle 1.8 mm
If
another paint is on the surface, after pretreatment
Apply
INTERPLAN 750PC 1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3)
nozzle 1.8 mm
Allow
the primer to dry for 10-15 minutes at 20°C
= 68°F
Apply INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow to dry overnight if possible or force dry
at 60°C=140°F for 20 minutes after a flash
off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An optional coat of INTERPLAN 650B gives optimal
protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
REMARKS
- Viscosity depends on humidity and temperature
- Always dilute with clean water
- Never use any soap during the process
3
DECORATIVE FILMS
PRETREATMENT
Gently
scuff sand the surface preferably with Scotch Brite
red type A very fine or sanding paper grade P380
or grade P240.
Use
INTERPLAN EED or Iso Propyl Alcohol to clean and
degrease.
Let
the surface dry for 5-10 minutes at 20°C = 68°F
APPLICATION
Apply
INTERPLAN 750PC primer
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.6 or 1.8 mm
Allow to dry for 10-20 minutes at 20°C = 68°F
Add
maximum 4 % by weight INTERPLAN Enhancer to INTERPLAN
1065B for better cleanability and optimal smoke
and stain resistance.
Apply
a cross coat of the INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
3
DECORATIVE FILMS
PRETREATMENT
Gently
scuff sand the surface preferably with Scotch Brite
red type A very fine or sanding paper grade P380
or grade P240.
Use
INTERPLAN EED or Iso Propyl Alcohol to clean and
degrease.
Let
the surface dry for 5-10 minutes at 20°C = 68°F
APPLICATION
Apply
INTERPLAN 750PC primer
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.6 or 1.8 mm
Allow to dry for 10-20 minutes at 20°C = 68°F
Add
maximum 4 % by weight INTERPLAN Enhancer to INTERPLAN
1065B for better cleanability and optimal smoke
and stain resistance.
Apply
a cross coat of the INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
4 DECORATIVE FILM, SLIGHTLY DAMAGED
PRETREATMENT
Dry
sand the damaged area with sanding paper grade P220
or P240 or with Scotch Brite red type A very fine
Remove dust of with clean water and a damp cloth
or with Iso Propyl
Alcohol or INTERPLAN EED.
Allow
to dry for 5-10 minutes at 20°C = 68°F
APPLICATION
Use
a brush or spray gun to apply INTERPLAN 750PC
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
on
damaged area’s
Allow
to dry for 10-15 minutes at 20°C = 68°F
Use
INTERPLAN 100SP fine to repair damaged areas by
applying thin coats with a flash off time of 10
minutes
Allow
to dry for 10-20 minutes at 20°C = 68°F
Dry
sand repaired spots with sanding paper grade P180
or P220
Remove
dust with clean water and a damp cloth
Allow
to dry for 10-20 minutes at 20°C = 68°F
- Add maximum 4 % by weight INTERPLAN Enhancer to
INTERPLAN 1065B for better smoke and stain resistance
and cleanability
Apply
a cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
5
DECORATIVE FILM, HEAVILY DAMAGED
PRETREATMENT
Remove
the entire film from the surface
Sand
the remains with sanding paper grade P60 or P80
according to surface and material
Use
Iso Propyl Alcohol to degrease.
Allow
to dry for 5-10 minutes at 20°C = 68°F
APPLICATION
Apply
INTERPLAN 750PC or INTERPLAN 750M primer depending
on the substrate
1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow to dry for 10-15 minutes at 20°C = 68°F
Repair
any damage with INTERPLAN 100SP or INTERPLAN 100SP
fine
Allow to dry overnight if possible as a longer drying
time will result in a better repair.
Dry sand repair spots with the appropriate grade
of sanding paper depending on the structure of the
repair.
Remove dust with damp cloth and clean water or Iso
Propyl Alcohol
Allow
to dry for 10-20 minutes at 20°C = 68°F
If needed a thin coat of INTERPLAN 100SQ may be
applied
1)
viscosity ± 60 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 or 2.0 mm
Allow
to dry for 30 minutes at 20°C = 68°F
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
6
HONEYCOMB, NEW
PRETREATMENT
Gently
scuff sand the surface with Scotch Brite red type
A very fine or sanding paper grade P240
Use
Iso Propyl Alcohol to clean and degrease.
Let
the surface dry for 5-10 minutes at 20°C = 68°F
APPLICATION
Apply
a thin coat of INTERPLAN 750PC
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry for 20-30 minutes at 20°C = 68°F
Apply
INTERPLAN 100SP fine over the whole panel with a
cloth, paper or a flexible plastic spatula to fill
the pores.
Straight
away wipe it of with a wet cloth or sponge and clean
water, so that only the small pores are filled
Allow
to dry for 10-20 minutes at 20°C = 68°F
Apply
a coat of INTERPLAN 100SQ to fill any remaining
pores
1) viscosity ± 60 sec Din cup 4
2) air pressure 3-4 bar – 45-60 psi
3)
nozzle orifice 1.8 or 2.0 mm
Allow to dry for 60 to 90 minutes at 20°C =
68°F or let dry overnight
If
necessary sand with sanding paper grade P180 or
P220
Remove
dust with clean water and a damp cloth
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
7
HONEYCOMB, PAINTED
PRETREATMENT
Scuff
sand surface with sanding paper grade P180 or P220
Remove
dust with a damp cloth and clean water or with Iso
Propyl Alcohol
Allow
to dry for a few minutes
APPLICATION
If
the substrate is not painted with HSH paint, apply
a thin coat of INTERPLAN 750PC primer.
1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow to dry for 10-15 minutes at 20°C = 68°F
Repair
damaged areas with INTERPLAN 100SP and INTERPLAN
100SP fine
Depending
on thickness, allow to dry for 60-90 minutes, dry
overnight or force dry at 60°C=140°F. When
force drying apply flash off time of 30-60 minutes
Sand
repair-spots with sanding paper grade P180 or P220
for SP fine and grade P60 or P80 for SP
Remove dust with airflow and a damp cloth with clean
water or Iso Propyl Alcohol
Allow
to dry for 10-15 minutes at 20°C = 68°F
Apply
a thin coat of INTERPLAN 100SQ to fill any remaining
pores
1) viscosity ± 60 sec Din cup
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 or 2.0 mm
Let
dry for 60-90 minutes at 20°C = 68°F
Sand
if necessary with sanding paper grade P220 or P320
Remove
dust with airflow or a cloth and clean water or
Iso Propyl Alcohol
Allow
to dry for 10-15 minutes at 20°C = 68°F
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
8 KYDEX PANELS
PRETREATMENT
Clean
substrate with INTERPLAN EED
Allow
to dry for a few minutes
APPLICATION
Apply a thin coat of INTERPLAN 750PC primer.
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow to dry for about 20 minutes at 20°C =
68°F
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
9 LAMINATE
PRETREATMENT
Degrease
and clean with Iso Propyl Alcohol
APPLICATION
Apply
a thin coat of INTERPLAN 750PC primer.
1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3) nozzle orifice 1.8 mm
Allow to dry for about 20 minutes at 20°C =
68°F
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow to dry overnight if possible or force dry
at 60°C=140°F for 20 minutes after a flash
off time of 10-15 minutes
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
10 LEATHER, ARTIFICIAL LEATHER AND P.U.FOAM
PRETREATMENT
Clean
with INTERPLAN EED and a cotton cloth.
- Check for compatibility (attacked or dissolved
substrate)
Allow
to dry for 10-20 minutes at 20°C = 68°F
Loose
paint should be removed and surface should be wet
sanded with Scotch Brite red type A very fine and
INTERPLAN EED
APPLICATION
Apply
INTERPLAN 1025 with a brush, spray gun or with a
clean paper/cotton cloth to fill small pinholes
Allow
to dry for ± 30 minutes at 20°C = 68°F
Apply
a cross coat of INTERPLAN 1050HF
1) viscosity 40-45 sec Din cup 4
2)
air pressure 2-4 bar = 30-60 psi
3)
nozzle orifice 1.8 mm
For
better smoke and stain resistance and cleanability
maximum 4% by weight INTERPLAN Enhancer may be added
to the INTERPLAN 1050HF
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
11
MDF
PRETREATMENT
Clean
the substrate with Iso Propyl Alcohol
APPLICATION
Apply
INTERPLAN 135 wood sealer as is.
Allow
to dry for 20 minutes
Apply
if necessary INTERPLAN 100SQ to fill possible pores
1) viscosity ± 60 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 2.0-2.2 mm
Sand
gently if needed with sanding paper grade P240 or
P400
Remove
dust with water and damp cloth or airflow.
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An optional coat of INTERPLAN 650B gives optimal
protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
REMARKS
- Viscosity depends on humidity and temperature
- Always dilute with clean water
- Never use any soap during the process
12 MEALTRAYS
PRETREATMENT
Scuff
sand gently with Scotch Brite red type A or dry
sand with sanding paper grade P180 or P220
Remove
dust with a damp cloth and clean water or Iso Propyl
Alcohol
Allow
to dry for a few minutes
APPLICATION
Apply
a thin coat of INTERPLAN 750PC
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry for 10-15 minutes at 20°C = 68°F
Use
INTERPLAN 100SP or INTERPLAN 100SP fine for repairs
if needed
Sand
these repair spots with sanding paper grade P220
to P320
Remove
dust of with a damp cloth and clean water
Allow
to dry for a 10-15 minutes at 20°C = 68°F
Add
4% INTERPLAN Enhancer to INTERPLAN 1065B and check
specified viscosity.
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
13 MELAMINE AND HARDBOARD
PRETREATMEN
Scuff
sand gently with Scotch Brite red type A very fine
or sanding paper grade P240
Degrease
and clean substrate with a damp cloth and clean
water or with Iso Propyl Alcohol
APPLICATION
Apply
a thin coat of INTERPLAN 750PC
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry for 10 minutes at 20°C = 68°F
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
REMARKS
- Viscosity depends on humidity and temperature
- Always dilute with clean water
- Never use any soap during the process
14 PANELLITE
PRETREATMENT
Scuff
sand substrate gently with Scotch Brite red type
A very fine or with sanding paper grade P240 or
P320.
Clean
surfaces with damp cloth and clean water or with
Iso Propyl Alcohol
Allow
to dry for 20 to 30 minutes
APPLICATION
Apply
according the surface a dustcoat or a covering coat
of INTERPLAN IP 750PC
1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
If necessary make any repairs with INTERPLAN 100SP
or INTERPLAN 100SP fine
Allow
the repair spots to dry and sand the surface.
Clean
surface with damp cloth and water, airflow or Iso
Propyl Alcohol.
After
10-15 minutes drying apply one cross coat of INTERPLAN
1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
-
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
15
PLASTIC, NOT PAINTED
PRETREATMENT
Scuff
sand substrate gently with Scotch Brite red type
A very fine or with sanding paper grade P240 or
P320.
Clean
surfaces with damp cloth and clean water or with
Iso Propyl Alcohol
Allow
to dry for 20 to 30 minutes
APPLICATION
Apply
a thin coat of INTERPLAN 750PC
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle 1.8 mm
Allow
to dry for 10-15 minutes
If
necessary make any repairs with INTERPLAN 100SP
or INTERPLAN 100SP fine.
Allow
to dry depending on applied thickness.
Sand
the dried surface with sanding paper grade P180-P240
Clean
surface with damp cloth and water, airflow or Iso
Propyl Alcohol.
Allow
to dry for 10-15 minutes
Apply
one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or force dry at 60°C=140°F
for 20 minutes after a flash off time of 10-15 minutes.
After
10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1) viscosity 30-35 sec Din cup 4
2)
air pressure 2-3 bar = 30-45 psi
3)
nozzle orifice 1.8 mm
REMARKS
-
Viscosity depends on humidity and temperature
-
Always dilute with clean water
-
Never use any soap during the process
16 PLASTIC, PAINTED
PRETREATMENT
Scuff
sand substrate gently with Scotch Brite red type
A very fine or with sanding paper grade P240 or
P320.
Clean
surfaces with damp cloth and clean water or with
Iso Propyl Alcohol
Allow
to dry for 20 to 30 minutes
APPLICATION
If the substrate is not painted with HSH paint,
apply a thin coat of INTERPLAN 750PC primer.
1) viscosity 40-45 sec Din cup 4
2) air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry for about 20 minutes at 20°C = 68°F
If
painted with HSH paint sand slightly with sanding
paper grade P220 or P320
Remove
dust with damp cloth and clean water or airflow
or Iso Propyl Alcohol
After
drying apply one cross coat of INTERPLAN 1065B
1) viscosity 40-45 sec Din cup 4
2)
air pressure 3-4 bar = 45-60 psi
3)
nozzle orifice 1.8 mm
Allow
to dry overnight if possible or
After 10-20 minutes drying time at 20°C = 68°F
special effects like leather look or marble may
be applied.
An
optional coat of INTERPLAN 650B gives optimal protection
1)
viscosity 30-35 sec Din cup 4
2) air pressure 2-3 bar = 30-45 psi
3) nozzle orifice 1.8 mm
REMARKS
- Viscosity depends on humidity and temperature
- Always dilute with clean water
- Never use any soap during the process
EXCERPT
OF HSH PRODUCT RANGE
PRIMERS
AND SEALERS
INTERPLAN
750M
primer
for direct application on metal
application
viscosity 40-45 seconds Din cup 4
air
pressure 2-4 bar = 30-60 psi
nozzle
orifice 1.8.mm
can
be applied on ferrous and non ferrous substrates
available
in various colours
INTERPLAN 750PC
primer for composites and plastics, honeycomb and
polycarbonates, PEI and PPS, synthetic substrates
application
viscosity 40-45 seconds.Din cup 4
air
pressure 2-4 bar = 30-60 psi
nozzle
orifice 1.8 mm
available
in various colours
INTERPLAN 1025 SEALER
sealer
for flexible substrates
can
be applied by brush, cloth or gun
used
for seat arm caps, flight crew seats and can be
applied on polyvinyl fluor films
FILLERS
INTERPLAN
100SP
ready
to use on any commonly used surface treated with
INTERPLAN 750M or INTERPLAN 750PC
used
for average repairs
can
be coloured according the colour of the topcoat
that will be applied.
INTERPLAN 100 SP fine
ready to use on any commonly used surface treated
with INTERPLAN 750M or INTERPLAN 750PC
used
for small repairs and for filling small pores after
application of INTERPLAN 100SP
used
on new panels to fill the small prepreg pores
can
be coloured according the colour of the topcoat
INTERPLAN 100SQ
spray
filler for filling pinholes or for filling remaining
small holes after a repair
viscosity
± 60 seconds Din cup 4
air
pressure 3-4 bar = 45-60
nozzle
orifice 1.8-2.2 mm
can
be coloured according the colour of the topcoat
TOPCOATS
INTERPLAN
1000 high gloss
available
in most colours
viscosity
30-40 seconds Din cup 4
air
pressure 3-4 bar = 45-60 psi
nozzle
orifice 1.8 mm
INTERPLAN 1065B semigloss
available
in most colours
viscosity
40-45 seconds Din cup 4
air
pressure 3-4 bar = 45-60 psi
nozzle orifice 1.8 mm
INTERPLAN 1083 semigloss two-pack
mixed with hardener INTERPLAN 1041
supplied
in a one gallon kit of 3.6 kg base and 1.2 kg catalyst
available
in most colours
viscosity
mixed 37-43 seconds Din cup 4
air
pressure 3-4 bar = 45-60 psi
nozzle
orifice 1.8 mm
INTERPLAN 1050HF semigloss
high
flexible for application on flexible substrates
available
in most colours
viscosity
40-45 seconds Din cup 4
air
pressure 3-4 bar = 45-60 psi
nozzle
orifice 1.8 mm
PROTECTIVE
COATINGS
INTERPLAN
650B gloss or matt
hard
clear coat for extra stain and smoke resistance
available
in pearlescent shades as well
viscosity
30-35 seconds Din cup 4
air
pressure 2-4 bar = 30-60 psi
PAINT
ADDITIVES
INTERPLAN
ENHANCER 95
add
to all top- and protective coats except to INTERPLAN
1083 to obtain better performance in resistance.
Maximum 4 % by weight to be added followed by a
viscosity check. Add clean water to reach right
viscosity.
INTERPLAN PAINT DEFOAMER
to
be added to paints that will be applied by brush
or roller
maximum
2% by weight
INTERPLAN 10 SR
to
be used in high temperature surroundings to extend
drying time
maximum
2% by weight to be added to the paint
CLEANERS
INTERPLAN
150
non
crazing cleaner for normal cleaning
INTERPLAN 250
non
crazing cleaner for heavy duty cleaning like removing
graffiti etc ,
may
be diluted up to 10 times its volume in water.
INTERPLAN EED
general
purpose cleaner for plastic, honeycomb, decorative
films, leather, p.u.foams, etc.
RS-ZEL-OCT-2001
|
